Industrial textile-finishing machinery and pipework in a processing hall; illustrative photograph, not a Hubei Jintian facility.

PFD Fabric vs Greige and White: A Buyer’s Guide

“Greige,” “PFD” and “white” are sometimes used loosely in fabric enquiries. They should not be treated as interchangeable descriptions. A roll can look pale and still be at the wrong processing stage for the next operation. A buyer who wants a dye-ready base may receive loom-state cloth; another who asks for white may receive a base intended for later dyeing. The difference affects the process route, the quotation and the checks that should be completed before bulk approval.

For woven-fabric buyers, the safest approach is to name both the fabric condition and what must happen next. PFD describes a preparation stage. White describes an appearance or colour requirement. Greige describes cloth before wet preparation. None of these terms, on its own, is a complete technical specification.

Greige, PFD and white: what each term means

Term What the buyer is asking for What still needs to be confirmed
Greige fabric Woven cloth in its loom-state or unfinished condition, before the required wet preparation and final finishing. Whether size, oils or other process residues remain; who will carry out preparation; and which width and GSM apply at this stage.
PFD (prepared for dyeing) Fabric prepared for a specified dyeing route but not yet coloured to the final shade. The actual preparation steps, fibre compatibility, permitted auxiliaries or finishes, test requirements and post-process dimensions.
White fabric A fabric supplied to an agreed white appearance or whiteness requirement. Whether it is bleached, optically brightened or otherwise finished, and whether it is intended for cutting and sewing or for further coloration.
Solid-dyed fabric Fabric coloured to an agreed solid shade. The dyeing route, approved shade standard, finishing, fastness requirements and whether the quoted condition is finished bulk fabric.

The distinction between white and solid-dyed matters on a purchase order. White should be specified as white (or by the buyer’s agreed whiteness standard); it should not be grouped under a generic “solid-dyed” price line. A white base and a coloured solid shade are different commercial requirements.

What preparation does to woven cotton

Preparation is not simply a wash. The sequence depends on fibre content, construction, the intended colour and the process that follows. In woven cotton, warp yarns may have been sized to help them withstand weaving. That size must be removed when the next process requires a clean, evenly wettable surface. CottonWorks describes desizing as the wet process that degrades and removes size from warp yarns so the fabric can be dyed or finished evenly.

Scouring then removes surface waxes and other impurities that can interfere with wetting and level processing. CottonWorks’ scouring reference explains its role in cleaning the substrate for dyeing and finishing. Where a white base is needed for light or bright shades, bleaching may be part of the route. It is not safe to assume that every PFD order follows one identical sequence or that every fibre blend can be prepared in the same way.

After chemical preparation, rinsing and neutralising are important. Residual alkalinity or processing chemicals can affect the next stage. CottonWorks’ dyeing-preparation guidance discusses monitoring pH, alkalinity, absorbency and whiteness, and stresses that the process must be controlled and documented. Mercerising may be specified for some cotton qualities, but it is not a universal requirement for every PFD fabric.

Blended fabrics need particular care. A cotton/polyester construction contains fibres with different dyeing behaviour. The buyer and dyehouse should agree the intended shade route and how each component is expected to be coloured. Do not assume that a preparation sequence designed for 100% cotton automatically suits a polyester-rich or elastane-containing construction.

Why PFD is not a guarantee of finished-fabric performance

PFD is useful shorthand, but the letters do not tell the buyer everything needed for bulk approval. They do not, by themselves, establish that the fabric is pre-shrunk, dimensionally stable, optically white, free of every finishing agent or suitable for every dye class and print process.

Nor do they confirm the final width or GSM. Wet processing and finishing can change fabric dimensions and mass per unit area. State whether the quoted width and GSM are measured in greige condition or after preparation, and set the acceptance limits for the condition being purchased.

Finishing chemicals also matter. AATCC’s overview of textile chemicals and their functions identifies optical brightening agents as chemicals used to increase the whiteness of bleached fabric, and softeners as agents used to modify fabric hand. If the cloth will be dyed or printed later, the buyer should say which auxiliaries and finishes are permitted and ask the processor to confirm compatibility with the intended route. “PFD” alone is not a substitute for that agreement.

Choose the condition that matches the next operation

Choose greige when the buyer or nominated processor intends to control the preparation route and has the capability to handle loom-state fabric. The quotation should make clear that preparation, bleaching, dyeing and final finishing are not included unless stated.

Choose PFD when the next operation is dyeing and the buyer wants the fabric supplied in an agreed prepared condition. Name the fibre composition and dye route, then define the preparation and test requirements with the dyehouse. If the cloth is a blend, confirm the route for the complete construction rather than specifying it as if it were 100% cotton.

Choose finished white when the fabric is intended to remain white for cutting, sewing or another end use. State the required white appearance and whether optical brightener, softener or other finishes are allowed. If the fabric may later be dyed a darker shade, do not order simply by colour name; ask for a prepared base compatible with that later process.

Choose solid-dyed when the required outcome is a confirmed solid shade. The buyer should approve the shade standard or lab dip and state the required colourfastness and finishing. Keep this separate from white and from PFD in the quotation.

What to put in the fabric RFQ

A useful RFQ removes ambiguity before the sample stage. Instead of writing only “PFD white,” give the supplier and processor enough information to identify the correct route.

RFQ field What to write
Fibre and construction Exact fibre percentages, woven construction, yarn details and weave, as applicable.
Fabric condition Greige, PFD, finished white or solid-dyed. Do not combine these into one vague colour description.
Intended next process Piece dyeing, garment dyeing, printing or direct cutting and sewing.
Preparation route Required steps and any buyer restrictions on optical brighteners, softeners, repellents or other finishes.
Test and acceptance Agreed absorbency, pH, whiteness, residual-chemical, shrinkage and other requirements, with test methods and tolerances where specified.
Finished dimensions Target width and GSM after the stated preparation or finishing stage, including tolerances and the measurement condition.
Approval Lab dip, print trial or production trial requirements, plus the approved reference and bulk shade-control method.

For example, a buyer could write: “100% cotton woven fabric; condition PFD for the nominated piece-dye route; preparation steps and permitted finishes to be confirmed before order; width and GSM to be measured after preparation; absorbency and pH acceptance limits to be agreed; bulk shade subject to approved lab dip.” This is an example of clear wording, not a universal process recipe or a set of standard limits.

If pH is part of the approval, identify the test method. ISO 3071:2020 specifies determination of the pH of an aqueous extract of textiles and was confirmed current by ISO in 2025. The standard describes a test method; the buyer still needs to state the contractual acceptance range. A pH result alone does not prove that fabric is ready for a particular dyeing process.

Checks before releasing the lot

Before bulk material moves to dyeing, printing or cutting, compare the roll labels and paperwork with the purchase order. Check that the stated condition matches what was supplied, and that roll numbers and lot references remain traceable. Where required by the specification, review absorbency, pH, whiteness and dimensional results. Approve the lab dip or print trial against the agreed reference, then confirm width, GSM and shrinkage at the correct process stage.

Our greige fabric inspection checklist covers loom-state construction, defects and roll traceability. For pH testing, see the guide to ISO 3071:2020 and AATCC TM81-2022. A listed example of a prepared-for-dyeing construction is our PFD stretch satin fabric; its published specification should still be checked against the approved sample and order requirements.

Make the process stage explicit

The most expensive misunderstanding is often not a complicated technical defect. It is a difference in what the buyer thought was included. A supplier reads “white” as a finished colour; the buyer meant a dye-ready base. A buyer asks for PFD but has not decided whether the next process is piece dyeing or printing. A quotation compares greige width with finished width as though they were the same measurement.

State the fabric condition, the next process and the acceptance requirements together. Hubei Jintian manages spinning and weaving, while dyeing and finishing are arranged through approved third-party partners. A clear RFQ allows the required processing stage to be confirmed before price, lead time and bulk approval are finalised. To discuss a woven-fabric requirement, send the composition, construction, target width and GSM, fabric condition, shade or print route, quantity and destination through our current-price enquiry page.

Featured image credit: Photo by Lalit Kumar on Unsplash, used under the Unsplash License. The photograph shows a textile-finishing unit; it is illustrative and is not a Hubei Jintian facility.

Technical references

Scroll to Top
Verified by MonsterInsights