A fabric roll can contain several defects of different sizes. The four-point system converts those observations into a numerical score so a buyer and supplier can discuss roll quality using a consistent record. It is widely used in commercial fabric inspection, but the score is meaningful only when both parties agree on the inspection method, width basis and acceptance limit before shipment.
This guide explains the common commercial 1–4 point scale, shows the calculation, and lists the rules that should be written into a purchase order or quality agreement.
First, distinguish the commercial four-point scale from ASTM D5430
ASTM D5430-26 is the current ASTM test-method listing for visually inspecting and grading fabrics. The standard contains more than one point-assignment option. ASTM specifically warns that scores can vary when different options are used and recommends using the same option when purchaser and supplier results are compared.
The familiar four-point schedule below is a common commercial grading approach. Do not assume that every buyer’s manual uses exactly the same defect rules or that every four-point report is automatically an ASTM D5430 report. If a contract requires ASTM D5430, identify the agreed option and edition in the inspection instruction.
Common 1–4 point defect scale
In the commonly used schedule, a defect receives a penalty according to its measured length or width. A single defect is normally capped at four points under this commercial approach.
| Measured defect dimension | Approximate metric equivalent | Penalty |
|---|---|---|
| Up to and including 3 in | Up to 76.2 mm | 1 point |
| Over 3 in and up to 6 in | Over 76.2 mm and up to 152.4 mm | 2 points |
| Over 6 in and up to 9 in | Over 152.4 mm and up to 228.6 mm | 3 points |
| Over 9 in | Over 228.6 mm | 4 points |
These are the commonly published commercial bands; a buyer’s own procedure may define measurement, rounding, holes, tears, edge defects, continuous defects and minor imperfections differently. The written inspection standard takes priority.
How to calculate points per 100 square yards
After inspecting the agreed length of a roll, add the penalty points for all defects that count under the agreed rules. Normalize the total by the inspected fabric area.
Points per 100 sq yd = Total penalty points × 3,600 ÷ (Roll length in yards × Fabric width in inches)
The factor 3,600 comes from 36 inches per yard multiplied by 100 square yards. Use the width basis specified by the buyer. If the agreement uses usable or cuttable width rather than nominal width, record that explicitly.
Worked example
Assume an inspected roll is 120 yd long and 58 in wide. The inspection record contains:
| Defect size | Number of defects | Points each | Subtotal |
|---|---|---|---|
| Up to 3 in | 6 | 1 | 6 |
| Over 3 to 6 in | 3 | 2 | 6 |
| Over 6 to 9 in | 2 | 3 | 6 |
| Over 9 in | 1 | 4 | 4 |
| Total | 12 | 22 points |
Points per 100 sq yd = 22 × 3,600 ÷ (120 × 58) = 11.38 points per 100 sq yd (rounded to two decimal places).
For a metric report, the equivalent area-based formula is: Points per 100 m² = Total penalty points × 10,000 ÷ (Roll length in metres × Width in centimetres). Do not mix metres with inches or square yards with square metres.
What the score does—and does not—tell you
A normalized score makes rolls of different lengths and widths easier to compare under the same rules. It does not identify the type of defect, show where it occurs, or prove that a fabric is suitable for a garment. A low score can still hide a critical defect in a visible panel area, while a higher score may be driven by defects in an area that the buyer treats differently.
Some factories use 40 points per 100 sq yd as a working benchmark, but it is not a universal pass limit. Buyers and brands set their own acceptance criteria. A purchase order should state the actual limit and whether it applies to each roll, the lot average, or both.
Inspection rules to agree before bulk production
- Method and edition: identify the standard, edition and point-assignment option. If the buyer uses a proprietary manual, attach or identify that revision.
- Inspection width: state whether the calculation uses nominal, inspected, usable or cuttable width, and how selvedges are treated.
- Defect definitions: define holes, tears, stains, slubs, missing yarns, barre, shade variation, edge defects, continuous defects and repeated defects.
- Special scoring: state any per-yard cap, maximum points for one defect, critical-defect rule or exclusion. Do not assume another buyer’s rules apply.
- Sampling: specify how many rolls are inspected, how rolls are selected, and whether the full roll or a defined sample length is examined.
- Acceptance: state the maximum points per 100 sq yd and any separate roll-level, shipment-level, shade or critical-defect requirements.
- Evidence: require roll number, length, width, defect location, defect size, point value, total points, photographs and the inspector’s name/date.
Practical buyer checklist for a fabric inspection report
Before approving a shipment, check that the report identifies the fabric quality and colour, order or lot reference, roll number, inspected length, inspected width, inspection method and edition, every scored defect, total points, points per 100 sq yd, and the agreed acceptance limit. Ask for the actual defect map or photographs when a score is disputed; a single final number is not enough to investigate a claim.
For a broader incoming inspection sequence, see How to Inspect Woven Fabric Before Bulk Production. When preparing the purchase specification, also use the fabric RFQ checklist for apparel buyers and confirm the usable and cuttable width.
References and image credit
- ASTM D5430-26 — Standard Test Methods for Visually Inspecting and Grading Fabrics.
- V-Trust — Other Reference Standards: commercial four-point scale and worked calculation. The buyer’s own agreed criteria remain controlling.
Featured image: Photo by EqualStock on Unsplash, used under the Unsplash License. The photograph is illustrative and does not show a measured result for any particular roll.



