Wide view of the textile production floor at Hubei Jintian

Fabric Crease Marks After Dyeing: Causes and Prevention

A crease mark that remains after dyeing or finishing can be difficult to hide, particularly on a solid shade. Before attempting reprocessing, identify where the fold formed and check whether a correction could also change the fabric’s shade, width or handle.

Common causes of crease marks in fabric

  • Fabric rope formation or folds during wet processing.
  • Uneven movement, loading, or tension in processing equipment.
  • Fabric being stored or transported while damp or under pressure.
  • Finishing conditions that do not remove earlier fold marks.

How to investigate

  1. Record the fabric lot, color, roll numbers, and defect locations.
  2. Check whether marks repeat at regular intervals or appear randomly.
  3. Compare samples from affected and unaffected areas under consistent lighting.
  4. Review the wet-processing and finishing route with the technical team.
  5. Test any proposed corrective treatment on a controlled sample first.

Prevention

Review loading and fabric movement, avoid unnecessary pressure on damp fabric, and inspect the material after key processing stages. If a corrective finish is proposed, verify shade, hand feel, width, GSM, and other required properties afterward.

Buyer checklist

Agree visual acceptance criteria, inspection lighting, sample approval, and handling of any affected rolls before bulk production. Do not assume a crease mark can be removed without changing other fabric properties.

For a fabric inquiry, send the composition, construction, color, quantity, finish, and destination through our contact page.

Locate the stage where the crease was introduced

Map the crease direction and position on the roll, then compare samples before and after dyeing, drying and finishing if retained material is available. A crease that repeats at regular intervals may point to equipment or fabric movement; an isolated fold may be related to handling or packing. Record machine and lot references rather than relying on appearance alone.

Inspect whether the mark disappears after the agreed relaxation or finishing process and whether any attempted correction changes shade, width, handle or surface appearance. Approve the correction on a representative sample before treating the full lot. Keep photographs under consistent lighting and include the roll number so the production team can compare the same defect later.

How to distinguish a crease mark from other fabric defects

A crease mark is a visible deformation associated with a fold. It may be localised, or it may extend into a longer line when the fabric repeatedly folds in a similar position. A crease can also be accompanied by a shade difference, so inspect both the surface shape and the colour rather than recording every line as a dyeing shade defect. The Government of India’s 2024 CITS Sewing Technology handbook lists crease marks among fabric defects and notes that a localised crease mark may differ from a crease streak that extends along a roll.

Do not confuse a crease with bow or skew, which concern the alignment of filling yarns or pattern lines across the width. A crease changes the fabric surface through folding or deformation; bow and skew describe a distortion in the fabric geometry. If the defect is visible only as a colour band and the surface is flat, investigate shade variation as well as mechanical creasing.

Where to look for the cause

For fabric processed in rope form, start with how the rope enters, travels through and leaves the machine. A twisted or knotted rope, folds that do not open properly, unsuitable loading, or poor coordination between fabric movement and liquor circulation can allow the same area to remain folded. The Government of Ethiopia’s Ministry of Labor and Skills training module, Performing Dyeing Operations (Version 1, August 2022), identifies poor opening of the rope, rapid machine running, pump and reel-speed mismatch, and shock cooling of synthetic material among reported crease-mark causes.

Fabric construction also matters. The 2024 CITS handbook identifies inadequate preparation or relaxation, tight construction, high-twist yarns, dense fabric weight, machine suitability, incorrect loading and excessively rapid heating or cooling as factors to investigate. These are diagnostic possibilities, not a universal recipe: the effect of each factor depends on the fibre, construction, dyeing route and machine design.

A practical investigation sequence

  1. Map the defect. Record the roll number, position from the roll start, distance from the selvedge, direction, approximate length and whether the mark repeats. Photograph the area with a scale or reference point and consistent lighting.
  2. Compare stages. If retained samples exist, compare greige or pre-treated fabric with material after dyeing, drying and finishing. This helps narrow the stage at which the mark first appeared.
  3. Review the machine record. Check actual batch loading against the machine’s rated operating instructions, rope condition, fabric circulation, reel and pump settings, heating and cooling profile, and any interruptions or abnormal stops. Do not copy a setting from another machine or fabric quality.
  4. Check the material. Confirm construction, GSM, yarn characteristics, width, prior relaxation or heat-setting requirements, and whether the fabric was stored or transported in a compressed or folded condition.
  5. Run a controlled trial. Change one relevant variable at a time on a representative sample or trial batch. Record the setting and result so the team can tell which change helped and whether it created a new problem.

Prevention: control the process, not just the chemical recipe

Prevention begins with a loading and operating procedure suited to the fabric and the specific machine. Check that the rope is not twisted or knotted, that the fabric can circulate and open as intended, and that the batch is within the machine manufacturer’s loading guidance. Review fabric speed, circulation and temperature transitions together; changing one without checking the others can simply move the problem.

An anti-crease auxiliary may support lubrication and fabric movement where the process and chemical supplier recommend it, but it should not be treated as a substitute for correcting poor loading or circulation. Confirm compatibility with the dyeing recipe and finishing route, and trial any change for shade, surface appearance and handle. The CITS handbook identifies anti-crease agents during scouring as one possible preventive measure; it does not establish a universal dosage or machine setting.

After a corrective treatment, check more than whether the line looks lighter. Reassess shade, width, GSM, handle, surface appearance and the dimensional or performance properties required by the buyer. A treatment that improves the visible crease but changes another approved property may not be acceptable.

What buyers should record during fabric inspection

Agree the inspection method and defect classification before bulk production. For each affected roll, record the roll identity, defect position, approximate dimensions, whether the surface is physically deformed, any associated shade difference, and the agreed disposition. Keep an approved reference and evaluate samples under consistent conditions. Do not assume that every crease can be removed by pressing or reprocessing; the CITS handbook notes that a crease may remain when final pressing cannot restore the original condition.

If reprocessing is proposed, request a representative trial and approve it against the original specification before treating the full lot. Record the result by roll and lot, including any change in shade, width, hand feel or other agreed test result. This creates a traceable basis for accepting, sorting, reprocessing or rejecting the affected material.

Technical references

For related appearance problems, see our guide to uneven fabric dyeing and shade variation. When reporting a defect, include the construction, fibre content, colour, finishing route and roll details so the investigation starts with the right material and process information.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top
Verified by MonsterInsights