A fabric can withstand a substantial pulling force and still tear too easily once a cut has started. It can also pass a fabric strength test but fail at a sewn seam because yarns move beside the stitch line. These are different problems, and they need different tests.
When a report says that a fabric has “failed strength”, the first question should be: which property was measured, using which method, in which direction and on what condition of fabric? Without those details, a buyer and supplier can end up comparing numbers that do not describe the same behaviour.
Start by identifying the property
| Property | What the test evaluates | Examples of recognised methods |
|---|---|---|
| Tensile breaking force and elongation | How much force a defined fabric specimen withstands while it is pulled, and how far it extends at the specified point. | ISO 13934-1:2013 strip method; ASTM D5035-11(2024) strip method. |
| Grab breaking strength | Breaking force measured with a grab-type specimen arrangement. It is not the same procedure as a strip test. | ASTM D5034-21R25 grab test. |
| Tear force | The force required to continue a tear from a prepared cut or slit in the specimen. | ISO 13937-2:2000 trouser-shaped, single-tear method; ASTM D1424-25 falling-pendulum (Elmendorf-type) method. |
| Seam performance | How a sewn assembly behaves: the seam may rupture, or fabric yarns may move beside the stitch line. | Use the seam-strength or seam-slippage method named in the buyer’s specification. See our guide to seam slippage in woven fabrics. |
A tensile result is not a tear result. A grab result is not automatically interchangeable with a strip result either. ASTM’s guidance for D5034 specifically notes that there is no simple relationship between grab and strip test results. The specimen arrangement and the amount of surrounding fabric supporting the area being pulled affect the result.
Which tensile and tear methods should a buyer specify?
Tensile testing: ISO 13934-1 and ASTM D5035
ISO 13934-1:2013 determines maximum force and elongation at maximum force using a strip method. ISO states that it is mainly applicable to woven textile fabrics, including some stretch woven fabrics, and that it uses a constant-rate-of-extension (CRE) testing machine. The 2013 edition was reviewed and confirmed in 2024 and remains current as checked on 12 November 2026.
ASTM D5035-11(2024) covers raveled-strip and cut-strip procedures for breaking force and elongation. Its scope and specimen preparation rules matter: a raveled strip is used for suitable woven fabrics, while a cut-strip procedure is intended for other fabric types described in the method. Do not assume that a laboratory can change the strip preparation or specimen width and still report a directly comparable result.
Tear testing: ISO 13937-2 and ASTM D1424
ISO 13937-2:2000 measures the tear force of trouser-shaped specimens using a single-tear method. ISO reviewed and confirmed this edition in 2023; it remains current as checked on 12 November 2026.
ASTM D1424-25 uses a falling-pendulum, Elmendorf-type apparatus to determine the force needed to propagate a single-rip tear starting from a cut. ASTM notes that agreement between results can be difficult for some fabrics. The method also has scope limitations, so it should not be selected automatically for every knitted or unusual construction.
These standards describe different specimen shapes and test principles. A result from one method should not be converted into, or treated as equivalent to, a result from another unless the buyer and supplier have an agreed, technically justified comparison plan.
What to check when a fabric fails
Do not begin by blaming the yarn, loom or dyehouse. First make sure the result is valid and that the test actually represents the buyer’s requirement.
- Confirm the sample identity. Match the report to the fabric article, composition, construction, colour, finishing stage, roll or lot number and sampling date. A greige sample and a finished, coated or washed sample are not the same test material.
- Check the method and direction. Confirm the full standard number, part, edition and procedure. Record whether the specimen was cut in the warp or weft direction. A report that does not identify direction is difficult to use for a woven fabric.
- Review specimen preparation and test conditions. Check specimen dimensions, edge preparation, conditioning, wet or dry state, grip arrangement and machine setup against the selected method. Do not compare results from different setups as if they were one series.
- Look at how the specimen failed. A break in the test area, a tear that travels from the prepared cut, slippage in the jaws and damage at a clamp edge are not the same observation. Ask the laboratory to record an unusual failure mode and determine whether the result is valid under the method.
- Compare warp and weft separately. If only one direction is low, review the yarn specification and condition in that direction, the construction, and the sample orientation. If both directions are low, broaden the investigation to the fabric lot, processing history and test setup.
- Trace the processing route. Review relevant records for dyeing, bleaching, washing, heat setting, resin or other chemical finishing, coating and garment-laundry treatment. These processes may affect fabric properties, but the effect must be established by testing the actual material rather than assumed.
- Retest a traceable retained sample when needed. If the result is disputed, agree the sample identity, test method, number of specimens and laboratory before retesting. Keep the new report linked to the same lot and retained sample record.
Read the report without mixing up the numbers
For a tensile test, the report may include maximum force and elongation at maximum force. Elongation is a percentage calculated from the extension and the method-defined initial gauge length:
Elongation at maximum force (%) = extension at maximum force ÷ initial gauge length × 100
For example, if the initial gauge length used for an illustrative calculation is 100 mm and the extension at maximum force is 12 mm, the calculation is 12 ÷ 100 × 100 = 12%. This is only an arithmetic example; the actual gauge length, specimen preparation and calculation must follow the selected test method.
For tear testing, record the force unit and the method used. Do not compare an Elmendorf result with a trouser-tear result, or compare values reported in different units without a valid conversion and confirmation that the underlying methods are comparable. The same caution applies to specimen widths and grab versus strip results.
A useful report should identify the laboratory, sample and lot, standard and edition, procedure, fabric direction, conditioning and test state, individual readings, reported average, units, acceptance limit and any unusual failure observations. If the buyer’s specification requires additional statistics or a particular report format, agree those before testing.
Put the requirement clearly in the fabric RFQ
“Strength: minimum [buyer-approved limit] for [tensile breaking force / tear force]. Test the approved finished fabric in warp and weft using [full standard number, part, edition and procedure]. Report individual results, average, units, specimen conditioning, wet or dry state and any unusual failure observations. Use the same agreed method for approval and bulk inspection. No method substitution without written approval.”
Fill in the bracketed fields with the buyer’s actual requirement. There is no universal pass limit for every fabric: the acceptable value depends on the end use, construction, test method and buyer’s specification. Do not copy a limit from a different fabric or a report using another method.
For a wider review of report traceability and laboratory information, see our guide to reading a textile test report. For broader roll checks before shipment, use the woven-fabric inspection checklist.
What a tensile or tear test cannot tell you
Neither test, by itself, proves that a fabric will resist abrasion, meet a seam-slippage requirement, withstand repeated laundering or perform well in every garment application. Those properties need their own suitable methods and buyer limits. A fabric that passes one strength test should not be described as “durable” in every sense without evidence for the relevant use.
The practical lesson is straightforward: agree the property, method, direction, sample state and acceptance limit before bulk production. When a result is low, investigate the sample and the test procedure before deciding where the process failed.
Standards and method references
- ISO 13934-1:2013 — tensile properties of fabrics, strip method; confirmed current in 2024.
- ASTM D5035-11(2024) — breaking force and elongation of textile fabrics, strip method.
- ASTM D5034-21R25 — breaking strength and elongation of textile fabrics, grab test.
- ISO 13937-2:2000 — tear force of trouser-shaped specimens, single-tear method; confirmed current in 2023.
- ASTM D1424-25 — tearing strength by falling-pendulum (Elmendorf-type) apparatus.
These links identify the published methods and their scope. The full standards contain the controlling specimen, apparatus and procedural requirements; this article is a buyer-oriented explanation, not a substitute for the standard text.


